Big Picture Big Sound

I’ve had friends run Kove 12″s, 4 doors and 2 tweeters off a 5 channel amp before. I doubt it got the sub to it’s RMS rating, but it sounded pretty good and got the job done, I just wouldn’t recommend it like that. I want to amp my tweeters and 6X9’s and my sub, different amps for the subs and speakers I don’t understand how you do it because the speakers have to be hooked up to the head unit right?? The power lead connects from the amp positive terminal to your battery – you will have to route the leads under your carpet. The earth goes from your amp to a suitable earth i. The remote wire will run from your amp should be labelled remote on amp connection to the remote on the back of your headunit – this is almost certainly a blue wire and shouldnt be connected to anything else the remote tells the amp when to switch off. However, your passengers won’t like it, but who cares about them? Your remote wire carries power just like your power wire.

How do you wire 2 amps together ?

Onkyo TX-SV Receiver subwoofer pre out no sound Yes turing on the “A” speaker is required for the Onkyo, but that only turns on the 2 front speakers in the “A” speaker jacks. You may also need to check and see if the Onkyo has a menu selection in the setup menu that will turn on the sub woofer output on the back of the receiver. I have seen on countless occasions where people just have a hard time finding that sub woofer option on their receiver.

Feb 06,  · You’ll need something like a 2 channel or 4 channel amp for the door speakers and an amp for the subwoofer (this would be the better way to do it). I’ve had friends run Kove 12″s, 4 doors and 2 tweeters off a 5 channel amp before.

Email us at AskSandV gmail. They would be used equally for both movies and music. Also, how do you connect more than one subwoofer to a receiver? A big sub with a inch driver should easily deliver deep bass extension and powerful dynamics. On the other hand, with two or more subs—even ones with smaller drivers—you can expect smoother, better-defined bass over a wider range of listening positions in your room. Adding a second sub will help to even out those response peaks and dips.

The tests used the same material to evaluate a single unit with a inch driver, two inchers, and four 8-inchers. The incher delivered the most authoritative low end, but its pitch definition was left wanting compared with the smaller sub configurations. It also found that while the quartet of 8 inchers failed to deliver muscular bass, the inch pair was nearly as impressive as the inch sub on that front.

This lead the tester, Brent Butterworth, to conclude: But a pair of good inch subwoofers can get you close to the same experience—and also deliver better—balanced bass.

How Do I Hook Up a Subwoofer to My Vintage Receiver?

Watching a movie on a properly set up surround sound system, or listening to your music through a new set of speakers can be an amazing experience. But, the key to a great home theater isn’t just spending a lot of money. Setting up the system correctly is just as important as what you buy. This guide, very simply, walks through the basics of speaker placement, how to hook everything up, and how to change a few settings to really make your system shine.

Throughout this article are links to other articles that go into more depth on each topic. Be sure to also check out our related YouTube video discussions linked below for further insights.

Aug 05,  · The Wharfedale Pro Titans have an in-built mixer so you can plug a smart phone, i-Pod or i-Phone directly in with just one TRS cable.

Your Subwoofer—Wired for Sound Wiring configurations for any application You have more than one option for connecting your subwoofer to your amplifier. But first, you must take into consideration the need to match your amplifier, subwoofer and their impedance in order to obtain the highest performance from these components. The wiring diagrams, mentioned in the following paragraphs, are just some of the best options available to you.

Important To avoid your high-powered amplifier from overheating, as well as damage to both your amp and subs, the ohms you drive your amp with must not be lower than what it is designed to handle. Some low-impedance wiring diagrams are included. Voice Coils—Single or Dual A single subwoofer voice coil is equipped with 2 terminal posts. A dual subwoofer voice coil is equipped with 4 terminal posts. The impedances for these voice coils are 2-ohm, 4-ohm and 8-ohm. Things may get complicated when you wire dual voice coils and more than one subwoofer together.

MonoBox Powered Speaker

Lives for gear Most subwoofers have speaker level inputs as well as line level. Option 1 – Just run 2 sets of speaker cables from the amp Left amp output would have a single cable going to the sub Left input, and another single cable going to the NS10 Left input.

Oct 23,  · Someone told me before that you can hook up car subs and amps to a home stereo using a car battery, a converter and a couple wires. I haven’t tried any sort of setup.

The obd port looks like the picture below This port is located somewhere under your drivers dash, lay on the floor and look up. In some cars, it may be behind a panel, but almost all cars will have this port. From this port, information such as fuel, mileage, and other information comes out via data. Most importantly, it has power and ground. Do you have a new teen driver in your family, do you want to track your car for security or other reasons?

Track where your kids are, when they drive and if they are going too fast. See where your wife is and if she is stuck in traffic. If your car gets stolen, call the police with the exact location. Below are some devices we recommend after going through a few products. No extra fees for one year! And renewal is the same price as of this writing. Be advised of that.

[PART 2] Get Better Live Sound: How to Set Up PA Speakers

Speaker Connections for proper impedance match A note about amplifiers: You should always use the recommended load for your amplifier. However, if you must use a load other than the recommended load, here is a short guide. Most solid-state amplifiers would rather look at an open circuit no speaker at all than a load. Therefore, you can usually use a load that is higher than the recommended load.

Do not use a lower impedance load, as this could cause serious damage to your SS amp.

But the line-outs on a powered mixer work exactly the same as on an unpowered mixer, so these will work just fine with active speakers. – leftaroundabout Jul 26 ’14 at 1 Note that while on your specific mixer, it is only the NL2 speakon connectors on the back that are powered, some powered mixers may have powered 1/4″ jacks as well.

In the past, speakers were designed to reproduce bass frequencies, so the need for seperate subwoofers were non-existant. When the size of speakers began shrinking, the need for subwoofers to handle bass increased. In learning The ‘Bassics’ of Bass Management , you’ll discover that receivers figure out what speakers should get bass digitally, and send the appropriate bass information to a powered subwoofer using a line-level connection.

But before receivers were digital, bass management had to be handled by the subwoofer using a age-old technology. Subwoofers have undergone some serious change in the past decade. Intitially, most subwoofers were passive. A passive subwoofer does not have its own amplifier built in, and is therefore connected with speaker wire between the front or all speakers.

What makes it more confusing is that even newer powered subwoofers can be connected passively, which means that it is still connected in the same manner as a passive sub. This method of subwoofer hook-up is very common for those that use Bose speaker systems, or anyone with a passive subwoofer. In the Receiver The receiver’s “yes” or “no” setting for the subwoofer only applies if you own a powered subwoofer connected to the receiver using a line level RCA style cord.

5 Best Powered Car Subwoofers to Buy in 2018

It provides the deep bass that most speakers lack and enhances both music and movie soundtracks. Whether you have a powered or passive sub, you’ll need to get it connected to your amplifier for it to work. This is a line level connection, which means it is not amplified. This connection is useful for powered subwoofers only. Connect using speaker wire.

At the bottom, you can see that 2 ohm mono (two 4 ohm speakers bridged) is the same as 1 ohm stereo (four 4 ohm speakers per channel). The image below shows the DVC speaker wired to both channels of a stereo amplifier.

I use this for small church audiences. I am told it that my voice sounds very clear and the volume is very good, even from the back of the audience, without being too loud for the front row. One frustrating hassle is that the instructions are extremely brief. If you really search online you can find enough info eventually, but it takes time and persistence, It took me a few hours, over the course of a few days, to figure out how to make the most out of just plugging in my Shure vocal microphone.

I wondered and stressed for a day if I needed to buy a preamp, before I figured this trick on my own. I don’t like having to use my iPhone to operate the EQ. I don’t like having to have a mandatory third party remote control.

Edifier Global Sites

To order call Subwoofers are often misunderstood, both in name and in application. While they have a reputation for providing hefty bass lift, they need not be proverbial bulls in the china shop of your listening room. First, the basic definition: A subwoofer is a loudspeaker that produces low frequencies that augment and extend the bass output of a full-range loudspeaker system.

Aug 03,  · Both of these brands have high level inputs that you just hook up where your speakers hook up to your amp. They are very high impedence so the output of your amp is not affected. They can easily be used w/vintage equipment.

Call Description Alto Stealth Wireless System for Powered Speakers Unchain your speakers from the tangled mess that are signal cables, and instead replace them with the incredibly convenient Alto Stealth Wireless system! Establish a reliable wireless connection to your speakers and never worry about running hundreds of feet of cable again. Expand your PA system with additional stereo receiver packs for interference-free sound to an unlimited amount of speakers.

Enjoy faster setups, quicker teardowns, and eliminate complicated or unsightly cable runs, regardless of the venue. The Stealth Wireless professional audio transmitter system instantly establishes a hardy, unseen connection from the output of your mixer or DJ controller to the inputs of your powered speakers. Your days running and securing cables are a thing of the past. After the show, simply disconnect the system and you’re ready to go – who has time to wind up cables?

One more step

Yamaha DBR12 PA speaker Yamaha has been kind enough to loan us two PA speakers from their wonderfully affordable DBR line of powered speakers, so that we can highlight how they work, and define some commonalities they share with other speakers of the same type. A super nice touch that will cut or boost the necessary frequencies accordingly for each situation. Just as in the world of recording, where monitors come in both versions, so do speakers in the PA realm.

solved Need signal from car stereo to power subwoofer with no RCA hook up on powered subwoofers and one blue on the back of stereo solved To hook up a Sony powered subwoofer s.

These mistakes can range from simple problematic issues to things that could quickly lead to premature device failure. Let me quickly explain why. Every cable has inherent resistance. The thinner the cable, the more resistance the cable will have. There are other factors as well, but this is the big one. The more resistance a cable has, the more it will affect the frequency response which is possible at the end of the cable run.

The reason this is related is because the load the amplifier has to deal with when driving a pair of speakers, changes with frequency.

What’s missing? Tell us about it.

To roll off filter the signal fed to the Satellite speakers for biamplification, you must: Have a separate amp and preamp OR a receiver or integrated amp that allows you toseparate its amp and preamp stages. Use a surround sound processor or receiver that has built-in high-pass filters and a subwooferoutput jack. Page 9 powered subwooferspage 9If you are using two Subwoofers, run the left channel interconnect cable to the left Subwoofer andthe right channel cable to the right Subwoofer.

Page 10 powered subwooferspage 10play.

Jun 19,  · You’re welcome in advance. The sound card is “not providing any power,” true, but not in the way that you seem to be thinking. It sounds like your new speakers are just plain.

Efficient Amplifiers For amplifiers there is really only one choice: These ultra-efficient wonders are inexpensive but obscure. T-amps are available in a couple of different sizes, based on different amp chips: Most of the ones I can find are only sold direct from Chinese vendors through Ebay. This means they are cheap, but it will take 2 weeks to get it.

Please post if you know of other sources for these amps. I bought and tested several of the common amps I found on ebay. Note that there are many vendors on ebay all selling the same amps or copies of the same amps. The names of the amps get a bit confusing, its easier to go by the photos. How to find these on ebay. You will find tons of these amps.

Stand alone amps amps with a plastic or metal case: Dayton DTA-1 from parts-express. This amp includes a built-in battery holder.

How to Hook up a Subwoofer and get best Subwoofer at Best Price


Greetings! Would you like find a partner for sex? Nothing is more simple! Click here, free registration!